PUCEM

The Eurostep PUCEM HF trowel system is a floor finish of 8-12 mm that consists of a combination of polyurethane and cement. The PUCEM HF trowel system is often used in the industrial sector. • The PUCEM HF trowel system is wear-resistant and heavy-duty • The infill material provides anti-slip making it safe to walk on a wet floor. • PUCEM HF is liquid-tight and has excellent resistance to chemicals, oils and solvents • The seamless finish also provides an easy-to-clean surface that is hygienic • Extremely heat resistant and can therefore withstand hot water • Can be lubricated under a slope • The PUCEM HF trowel system adheres directly to the substrate and can be applied in one go without a primer • For the technical description, see: TDS • Follow the manual for optimal application of PUCEM HF. Pay particular attention to this (the manual in a nutshell)! 1. Clean and degrease the surface thoroughly. Do not apply the product at a floor temperature below 15° Celsius. 2. The cement veil disappears by (diamond) sanding or blasting. 3. Pour the A-component into a bucket and add the pigment paste. 4. Then add the entire contents of the B component to the A component and the pigment. 5. Mix for 30 seconds until a homogeneous mixture. 6. Add the filler and mix thoroughly for 1 minute until a lump-free mixture is formed. 7. Pour the mixture and spread it evenly over the subfloor with a floor trowel. Always pour the entire contents of the bucket at once to prevent a rapid reaction of material in the bucket. 8. Roll with a nylon fleece roller to roll away the application marks from the floor trowel. 9. Once the PUCEM HF has been applied, the floor must harden for approximately 10 hours.

The Eurostep PUCEM SL self-levelling system is a 4-5 mm floor finish consisting of a combination of polyurethane and cement. The PUCEM SL self-leveling system is often used in the industrial sector. • The PUCEM SL self-levelling system is wear-resistant and heavy-duty. • It is a smooth floor finish that is easy to maintain • PUCEM SL is liquid-tight and has excellent resistance to chemicals, oils and solvents. • The smooth finish also provides an easy-to-clean surface that is hygienic • Extremely heat resistant and can therefore withstand hot water. • Rapid build-up of high strength in a short time • For the technical description, see: TDS • Follow the manual for optimal application of PUCEM SL. Pay particular attention to this (the manual in a nutshell)! 1. Before applying PUCEM SL, first pre-treat the surface with PUCEM L as a primer to fill the pores of the surface. 2. Pour the A-component into a bucket and add the pigment paste. 3. Then add the entire contents of the B component to the A component and the pigment. 4. Mix for 30 seconds until a homogeneous mixture. 5. Add the filler and mix thoroughly for 1 minute until a lump-free mixture is formed. 6. Pour the mixture and spread it evenly over the subfloor with a floor trowel. Always pour the entire contents of the bucket at once to prevent a rapid reaction of material in the bucket. 7. Roll with a spiked roller.

The Eurostep PUCEM TF infill system is a 4-12 mm floor finish consisting of a combination of polyurethane and cement. The PUCEM TF infill system (infill material such as quartz sand) is often used in the industrial sector. - The PUCEM TF infill system is wear-resistant and heavy-duty. - The infill material provides anti-slip, making it safe to walk on wet floors. - PUCEM TF is liquid-proof and highly resistant to chemicals, oils and solvents. - The seamless finish also provides an easy-to-clean surface that is hygienic and meets the strictest food safety standards. - Extremely heat resistant and can therefore withstand hot water. - Rapid build-up of high strength in a short time Summary PUCEM TF infill system is a robust, strong and decorative floor that is heavy duty and easy to clean. Suitable for industries such as factories, garages and workshops. - For the technical description see: TDS - For optimal application of PUCEM TF infill system, follow the manual. Pay particular attention to this (the instructions in a nutshell)! 1. Thoroughly clean and degrease the substrate. Do not apply the product if the floor temperature is below 15° Celsius. 2. (Diamond) sanding or blasting removes the cement residue. 3. Pour the A-component into a bucket and add the pigment paste. 4. Then add the entire contents of the B component to the A component and pigment. 5. Mix for 30 seconds until a homogeneous mixture is formed. 6. Add the filler and mix thoroughly for 1 minute until a lump-free mixture is formed. 7. Pour out the mixture and spread it evenly over the subfloor with Tooth Strip 28cm, 4700-280-S 10. Let it flow for about 10 minutes before you start spreading. Always pour the entire contents of the bucket at once to prevent rapid reaction of material in the bucket. 8. Depending on the desired anti-slip level, sprinkle full and saturated with 0.4 - 0.8 mm or 0.8 - 1.2 mm quartz. 9. When the PUCEM TF has been applied, the floor should cure for about 10 hours. 10. Remove excess quartz from the floor and resand with a rotary parquet sander if necessary. ALWAYS finish the floor with PUCEM L